The model is equipped with the connector of 6 pins. The light bulbs are used as lighting. That is "+" for the bulbs taken from the track. I decided to begin to remake the light on the LED. "+" take from the decoder.
To disassemble the model read the instructions or look
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
After removal of all boards, we start changeover of bulbs. For a start we cut tracks
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
solder resistors
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
then from residuals of a prototyping board, I made the base on which I will solder a LED
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
further we solder wires to a board
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
and a LED which soldered to preparation from a prototyping board
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
From the tender to the engine there are 5 wires (a track of 2 pieces, the motor of 2 pieces and "-" for light back buffer lamps), in a connective crosspiece, which not folding. We need to stretch through it still a "+" wire, the benefit a place is, but simply it won't turn out. For this purpose we take a thin wire and we stretch
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
then the blue wire is soldered to it and we drag it through a crosspiece, then unsolder the wire.
At boards of the tender we cut tracks
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
we solder resistors and a LED
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
then on a double-side adhesive tape we paste a LED into place where there was a lamp
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
As the place is practically not present under the decoder and the speaker, decided to take out weight from a boiler, for this purpose it is necessary to unstick accurately a furnace leaf from a boiler. weight isn't fixed in a boiler, it is simply inserted into tension. We take out weight and we see that in it there is a dredging. We paste the speaker and the decoder on a double-side adhesive tape
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
also we push everything back in a boiler.
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
We paste into place a furnace leaf.
In the engine we remove 6 pins the connector and we do 8 pins of
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
We solder wires to the connector which go from the tender and a board of the engine. We put an engine board into place, a LED on a double-side adhesive tape to the place of a bulb.
Now on a double-sided adhesive tape we paste 8 pins the connector into place where there were 6 pins earlier and we connect the decoder
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
Also we put a boiler on the place
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
Further we assemble the locomotive and we check
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
We watch result