Installation of sound decoder
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
remove the condenser
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
make one red lantern
on a back edge board we drill the transition sleeve between board layers
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
on a front board we cut the track
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
To make the shunting mode, we should separate white buffer lamps from a projector and bonnet tables, then to connect them to red lamps.
With a reverse side of a board, we cut the track
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
on the other side of the board cut also one track (drawn in red), and then solder the wires (painted white, which points need to be wired)
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
Now we do the shunting mode.
we cut the track on a front edge board (it is shown red)
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
also we solder the diode and a wire
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
then on a back edge board we cut the track
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
also we solder the diode and a wire
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
on each wire from edge boards we solder the diode
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
and then on it we seat thermoshrinkage
and we connect two of these wires among themselves and we solder the collet dowel which too we pack into thermoshrinkage, that is it turns out so
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
Decoder of firm of Modelldepo. micro SoundGT2 plux16
the decoder of plux16 at us. And the connector on plux12 board, it is possible to bite off completely 4 pins or to truncate them (that they didn't rest against a board)
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
we solder to the decoder conductings with reverse collet a pin (a pin we pack into thermoshrinkage)
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
In such a way we will connect shunting light to the decoder. I made the connector in order that it was possible to remove the decoder without soldering of wires, you can solder without connector to the decoder.
here we solder wires from the speaker to these pins of a board
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
we paste the speaker 11x15x12 on a double-side adhesive tape to the place of the dismantled condenser (see a photo above)
And then we should grind off a little a weight (about 2 mm are shown red) that the decoder didn't rest against it.
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
and then to paste an insulating tape on this load (a blue arrow it is specified where) that when the decoder "will sag" under the weight I didn't concern metal.
Light in a cabin.
here so the cabin looks
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
That is "ceiling" isn't present and the light waveguide from a projector is visible.
We simply from polystyrene cut a ceiling. Then we take смд a LED and we solder to it wires. We drill a hole in a ceiling under wires, we pass LED wires throughout these holes and we paste a LED to a ceiling. Then we paste a ceiling in a cabin and we receive
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
we don't forget to solder resistors to wires of this LED, and then "+" we solder to a board
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
and "-" via the connector (collet pins) or directly to the decoder (a black wire on a photo)
*** Der Link ist nur für Mitglieder sichtbar. Bitte registriere Dich, oder logge dich ein. ***
Then it is necessary to collect model and to set up the decoder.
As a result we receive: